Fixing Thread Tension Issues
By Admin on January 16th, 2017

Addressing Tension Issues are basically a series of adjustments, and understanding how to do so.
 
There are several factors that go into tension issues that arise while sewing. While frustrating, it's usually a simple fix once you understand how it's controlled.
 
Things that affect the tensions on your machine. Check in the order as listed...

  1. Make sure your machine has been cleaned , serviced (adjusted & lubricated).  A machine should be serviced a minimum of once per year. A machine that is used daily should be lubricated weekly or biweekly. Even if a machine sits in storage for 6 months and was serviced prior, it should be serviced again once pulled from storage.  Part of servicing includes removing the parts from the bobbin case area, and cleaning and inspecting it. Even one stuck thread in the bobbin area can wreak havoc while trying to sew.  I've even seen threads caught around balance wheels, preventing the machine from operating. Dirt, old gummy oil and lint buildup in the machine will also keep it from running smoothly. Tip: keep a can of compressed air handy to periodically clean out under the feed dog and bobbin case area as lint will build up quickly.
  2. Use the correct weight thread for the fabric weight you are sewing. There's a needle & thread chart in every user manual. Do not use old thread.
  3. The needle should be new. (however, even new needles sometimes are defective). It's recommended to change needles after each big project, as they can wear or develop burrs which will tear your thread.
  4. Make sure the needle is inserted correctly into the needle clamp. Refer to your manual as machines will differ.
  5. Using the correct needle size for the fabric you are sewing.  *the needle, thread and fabric all should be compatible.
  6. Proper upper threading of the machine. Note: There are thread guides on every machine, these guides play an important part with controlling the thread tension as well. Refer to your manual for the proper threading procedure for your machine.
  7. Proper bobbin case threading. Refer to your manual as machines will differ.
  8. Presser foot tension- There is a pressure regulating screw on the top left of the machine, this controls the amount of pressure the foot puts on the fabric while you sew. Turning left loosens the pressure, and turning it right adds more. Always turn in small increments until you reach the desired pressure on the fabric.
  9. Upper thread tension assembly- when you thread the machine, the thread will pass through this, again be sure that the thread is guided through it properly, or it won't work properly. Never take apart an upper thread tension assembly unless you are 100% sure how to put it back together, because it can be troublesome. Again, turn the knob left to loosen, or right to tighten the tension on the thread. *Always adjust this in small increments until the desired tension is achieved.
  10. Make sure the thread is inserted in the correct direction through the eye of the needle. Refer to your manual as this differs with various machines. 
 
Okay, so let's assume you've gone through this checklist and are confident that everything is threaded properly and ready to go. Take a sample of the same fabric that you are using for your project and test your tensions.  Start sewing about 10-15 stitches or so, then stop and check out the top and bottom stitches....
 
How do they look?
 
*If the BOTTOM stitches are 'loose & loopy’, this means that the tension is too loose and an UPPER  thread tension adjustment is needed.  Turn right to increase the tension, about one 1 number at a time, and then try sewing again. If your machine is much older and there are no numbers on the assembly, simply turn the knob in small increments until the desired tension is achieved, testing the stitches as you adjust. NEVER TURN THE TENSION ASSEMBLY UP TOO MUCH AT ONCE. Repeat until the bottom stitches are no longer loose. Note: If increasing the tension does not correct the stitches, there may be an issue with your tension assembly.
 
*If the TOP stitches are loose (which rarely occurs), then this means that your bobbin case tension needs to be adjusted. Bobbin cases have a tiny screw. With a small screwdriver, turn the screw to the right to increase the tension JUST A HAIR. Then test sew a few stitches to see if it corrected the issue. In my personal experience it's been rare that I ever had to adjust bobbin case tension, but I have.  Note: if your top stitches remain loose no matter what you do, remove the upper spool of thread entirely and use another. It means that the thread is not compatible.
 
 
Other things to check:
 
Look at the fabric- How does it look? Is the fabric 'puckering'  while you sew? If so, loosen the pressure regulating screw on the top of the machine by turning just a little to the left.  When the fabric puckers, or bunches up somewhat, it means that too much pressure is being put on the fabric as it feeds. Just loosen the screw a little, test sew again, and keep adjusting the screw until the fabric no longer puckers. The fabric should remain flat and stay smooth while you are sewing.
 
Note: In some instances the upper thread tension assembly may be broken. Sometimes people might remove it and put it back without doing it properly. There's also a check spring in this assembly that sometimes breaks, is bent, or is inserted into the assembly wrong when it's removed.  The check spring plays an important part in controlling the thread as it passes through it. Check to see if the spring still has a 'spring' to it, if it does, it's likely fine, if not, it needs to be replaced. Luckily, check springs and complete upper thread tension assemblies are still available for most machines.
 
Basically that's it. Proper upper and lower threading, compatible thread, needle and fabric and a clean lubricated machine are all you need to sew with success.